Your Complete Tutorial for Bathtub Installation
Your Complete Tutorial for Bathtub Installation
Blog Article
This post which follows involving How to Install a Bathtub Yourself is especially entertaining. You should take a peek.
Mounting a bath tub isn't precisely rocket science, yet it does need strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a brand-new one is also a moderately hard job. If the old tub is easily obtainable, the job can move quickly; if you need to open up a wall surface to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Ensure you have actually certified on your own for the work and also fit attempting it. Rather than working with a specialist to take control of a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This post will certainly assist you mount a brand-new bathtub in your shower room if you have already acquired a new tub as well as don't need to change the arrangement of your previous supply of water pipes.
Your tools and also product list ought to consist of the following:
Preparing for the Installation
Firstly, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps device to prevent strain on the tub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the water. After doing so, activate the taps to drain any water staying in the system. The process of eliminating the existing taps can be quite problematic because of the limited gain access to that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing substance.
Before going on to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the needed placement. The wood boards are valuable in evenly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the tub up until the spirit level reads degree.
To install faucets, fit all-time low of the outermost versatile tap adapter to the appropriate supply pipe by making a compression join; then do the same for the other faucet.
Activate the water system and examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill up the bath tub as well as likewise inspect the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub should wait till the bath tub has been used at least when as this will resolve it into its final setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making certain that the washing machines remain in area between the tap and the sink. Protect the faucet in position with the maker given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap ports. The previous kind ought to be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split an inflexible seal, triggering the water to permeate the wall surface between the bath as well as the tiling, leading to problems with wetness and also possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can split fairly very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily offered on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Put a short review down the page. We would be pleased to see your thoughts about this write-up. We are looking forward that you visit us again before long. Sharing is caring. Helping others is fun. I treasure reading our article about Installing A Bathtub.
Plumbing challenges? Get immediate solutions. Report this page